There are many reasons why ice machines don't make ice, but they can't do without the hardware of the ice machine. You can observe the abnormal situation first, then locate the fault point. After Zui, you can determine the crux of not making ice, so you can shorten the area quickly and accurately. Find the point of failure. The following is a summary of the ice machine failure analysis of ice making:
First, the amount of ice produced decreases , capillary or expansion valve plug.
2. There is a slight ice block in the system where the water is too high.
3. The condensing system of the ice machine is blocked.
4. Insufficient refrigerant or leakage.
5. The evaporator is too dirty.
Second, the machine runs but does not produce ice 1, the water tray is not enough or no water.
2. The gear unit is faulty or the geared motor.
3, the system is blocked by ice. Dirty blockage, etc.
4, ice machine leakage, the pressure is not enough 5, the ice is not thick enough
Third, the compressor interrupted work:
1. The voltage is too low. Check the power supply.
2, the contact point burning contact is not good.
3. System pressure protection.
4. The compressor starter is faulty.
5, the condenser is too dirty, high voltage protection.
4. The ice machine is leaking. 1. The water supply to the water inlet valve is too large.
2. The damaged water pipe is damaged.
3. The hose clamp is faulty.
4. The water level float valve is faulty.
5. Wet ice borneol is not hard 1. The ambient temperature is too high, especially in summer.
2, repaired machine refrigerant added.
3. The water supply of the ice machine water distribution tray is too large.
4. The power of the press is insufficient.
Sixth, the boot report system failure 1, phase sequence problem.
2. The power supply system is faulty.
3, the control board is faulty
7. The noise is too large and the ice machine fan is faulty.
2. The speed reducer is faulty.
3. The compressor is noisy.
Eight, water shortage alarm 1, water supply connector filter network blockage.
2. The water supply pipe is blocked.
3. The inlet valve is blocked.
4. The drain valve leaks.
5. The pump is faulty.
First, the amount of ice produced decreases , capillary or expansion valve plug.
2. There is a slight ice block in the system where the water is too high.
3. The condensing system of the ice machine is blocked.
4. Insufficient refrigerant or leakage.
5. The evaporator is too dirty.
Second, the machine runs but does not produce ice 1, the water tray is not enough or no water.
2. The gear unit is faulty or the geared motor.
3, the system is blocked by ice. Dirty blockage, etc.
4, ice machine leakage, the pressure is not enough 5, the ice is not thick enough
Third, the compressor interrupted work:
1. The voltage is too low. Check the power supply.
2, the contact point burning contact is not good.
3. System pressure protection.
4. The compressor starter is faulty.
5, the condenser is too dirty, high voltage protection.
4. The ice machine is leaking. 1. The water supply to the water inlet valve is too large.
2. The damaged water pipe is damaged.
3. The hose clamp is faulty.
4. The water level float valve is faulty.
5. Wet ice borneol is not hard 1. The ambient temperature is too high, especially in summer.
2, repaired machine refrigerant added.
3. The water supply of the ice machine water distribution tray is too large.
4. The power of the press is insufficient.
Sixth, the boot report system failure 1, phase sequence problem.
2. The power supply system is faulty.
3, the control board is faulty
7. The noise is too large and the ice machine fan is faulty.
2. The speed reducer is faulty.
3. The compressor is noisy.
Eight, water shortage alarm 1, water supply connector filter network blockage.
2. The water supply pipe is blocked.
3. The inlet valve is blocked.
4. The drain valve leaks.
5. The pump is faulty.
Ground-Inserting Micro-Spray,Rod-Inserting Micro-Spray,Fruit Tree Vortex Micro Nozzle,Greenhouse Hanging Micro Spray
Shandong Yibiyuan Water-saving Equipment Technology Co., Ltd. , https://www.cnybyjs.com